Reports The Airplane Was More Than 600 Pounds Overweight At Takeoff
An NTSB factual report for an accident which occurred in March of 2011 resulting in the fatal injury of four of the five people on board the airplane contains information showing the airplane was about 600 pounds over its maximum approved takeoff weight when it departed Long Beach, CA, airport, and both engines were due for a major overhaul. The pilot was also not observed conducting a pre-flight inspection of the aircraft.
The official factual report indicates that on March 16, 2011, at 1029 Pacific daylight time, a Beech Super King Air 200, N849BM (similar aircraft pictured in file photo), impacted terrain following a loss of control during takeoff from Long Beach Airport, Long Beach, California. The commercial pilot and four passengers were fatally injured; a fifth passenger was seriously injured. The airplane was substantially damaged. The airplane was being operated by Carde Equipment Sales LLC under the provisions of 14 Code of Federal Regulations Part 91. An instrument flight rules (IFR) flight plan had been filed for a cross-country flight to Salt Lake City, Utah, and the crash occurred on initial departure. Visual meteorological conditions prevailed at the time of the accident.
According to flight planning documents, about 0700, the pilot filed an IFR flight plan to fly from Long Beach to Salt Lake City. He was planning to fly the estimated 510-nautical-mile (nm) trip in 1:52 hours with three people.
Departure was planned for 0830. During the preflight of the airplane, the pilot had some difficulties with transmitting on the radios, which delayed the trip’s departure. He called the owner’s Aviation Manager, about 0845, for assistance. The two of them could not rectify the problem, so they walked to an adjacent building to talk with the Director of Maintenance for West Coast Maintenance. He and one of his employees suggested that they check the transmission switch position on the pilot’s oxygen mask. The two men departed and the radio transmission problem was corrected. The owner’s Aviation Manager stated that he did not observe the pilot perform the airplane's preflight; there were no witnesses identified who observed the pilot conducting the airplane’s preflight inspection on the morning of the accident.
The pilot boarded his two original passengers, plus three additional passengers, and prepared to start the airplane’s engines. At 1020, the pilot radioed the airport ground controller and requested taxi clearance to runway 30. A witness observed the airplane at the departure end of runway 30 prior to taking the active. He said it sat there for a few minutes doing some engine run-ups. At 1027, the local controller cleared the pilot for takeoff. Several witnesses reported that the initial ground roll appeared normal. Shortly after the airplane rotated and started to climb, it began to yaw left and level off. One witness said “the airplane sounded like it was in trouble.” Another witness said it sounded like one of the engine’s propellers “feathered, went to flat pitch or even went into beta mode, like a full power fan noise.” A third witness said “the strange noise was like a propeller noise, not an engine sound.” A fourth witness said that it appeared to
him that the left propeller was windmilling.
Several witnesses said that, as the airplane began to bank left, its wings wobbled and its fuselage fishtailed. As the airplane’s bank angle continued to increase, the airplane’s yawing progressed to a left skid “until it looked like it was going sideways.” One witness said that, as the skid continued to develop, he spoke aloud: “straighten it out, straighten it out, straighten it out.” The witness reported that the airplane’s “forward speed began to drop off and the airplane didn’t seem to have any lift.” As the bank angle increased to 45 to 90 degrees, the airplane’s nose dropped down to near vertical. One witness said that as the airplane approached the ground he heard an engine “power up and the nose jerked upward just prior to [the airplane] crashing into the ground.” Another witness said the bank angle and pitch “began to flatten out just before crashing down to the ground.”
On the morning of the accident, the director of maintenance (DM) for West Coast Aircraft Maintenance was in his office on the Long Beach Airport. The office building was near where the accident airplane was regularly parked, and about 2,000 feet from the departure runway. He heard a loud pop and then immediately another loud pop. He knew that sound wasn’t right for a departing airplane, and he immediately rushed to a doorway in time to see the accident aircraft just before it impacted the ground.
The witnesses reported that, on impact a fire erupted, which consumed the airplane. Airport fire and rescue personnel were at the scene in 3 to 5 minutes.
The 43-year-old pilot started his flight training in October 2001. At the time of the accident, he held a commercial pilot certificate with airplane single and multiengine land ratings, and an airplane instrument rating. His most recent first-class Federal Aviation Administration (FAA) medical certificate was issued on June 18, 2010. The pilot’s flight logbook and the airplane flight records indicated that the pilot had 2,073 hours of total flight experience. He had approximately 1,113 hours of multiengine time, of which 463 hours were in the make and model of the accident airplane. Approximately 665 hours of his total flight time was in light single engine piston aircraft. No documentation could be found to indicate that he had received any training in full-motion King Air simulators.
The pilot had been employed, in May 2005, by Ameriflight, Inc., Billings, Montana, as a second-in-command (SIC) pilot in a Beechcraft Model 99. In October 2007, West Coast Charters, Santa Ana, California, employed the pilot as an SIC pilot in a Beechcraft King Air 200, the same make and model as the accident aircraft. Most of his King Air 200 flight time was acquired at West Coast Charters. On October 19, 2010, Rainbow Air, Long Beach, hired the pilot to fly as a pilot-in-command (PIC) in a Beechcraft Model 90. On that date, he successfully passed a Part 135 check, which also qualified as his FAA required flight review. He began flying the accident airplane as a contract single pilot on January 2, 2011. Between January and the accident he was the only pilot who flew the airplane, and the airplane’s records indicate he made about 40 flights in it.
About mid-February 2011, the pilot flew with the owner’s Aviation Manager to Bellingham, Washington, and back. The Aviation Manager was never “checked out” in Beech King Air 200s; he was experienced in other corporate jets and turboprop aircraft. The Aviation Manager said that he helped prepare for the flight by fueling the airplane while the pilot performed a preflight inspection. The Aviation Manager did notice that the pilot drained one or more of the airplane’s 12 fuel sump drains, but he was not sure how many or exactly which sumps the pilot drained. He also observed that the pilot performed the draining while he was still fueling. Normal recommended procedures for draining fuel tank sumps is to wait at least 20 to 30 minutes after fueling to permit the settling of any water or any other possible contaminates.
The airplane was a twin engine, propeller-driven, eight seat, pressurized aircraft, which was manufactured in 1981 by Beech Aircraft Company. At the time of manufacture, the airplane was equipped with Pratt & Whitney Canada model PT6A-41 engines, each fitted with a Hartzell Propellers, Inc., three bladed propeller. Each engine was rated at a maximum takeoff rating of 850 shaft-horsepower. The airplane was later modified in accordance with Supplemental Type Certificates SA00433AT and SA2698NM-S, which installed Pratt & Whitney Canada model PT6A-42 turboprop engines, each fitted with a Hartzell Propellers, Inc., four bladed propeller. Each engine maintained the same maximum takeoff rating of 850 shaft-horsepower.
The four-bladed Hartzell propellers were constant-speed, full-feathering, and reversible. They were manufactured in June 1999. The airplane was equipped with an automatic feathering system, which was designed for use during takeoff and landing, and should be turned off when the airplane is established in cruise climb. If the power output was reduced in either engine during takeoff, once the engine’s torque dropped from 2,230 foot/pounds (ft/lbs) to about 220 ft/lbs, the propeller blades would move towards the feathered position. This system is operationally checked before every takeoff, as required in the Pilot’s Operating Handbook, Before Takeoff (Run-up) checklist.
The owner bought the airplane on August 12, 2009. It received its most recent annual inspection on August 9, 2010. According to airplane flight records, at the time of the accident, the airplane had flown 9,133 hours; the left engine had 5,695 total hours and 3,020 hours since its last overhaul; the right engine had 5,613 total hours and 3,325 hours since its last overhaul. The engine manufacturer recommends that the engines be overhauled every 3,000 flight hours. The propellers were installed about August 1999. The propeller manufacturer recommends that they be overhauled every 3,000 flight hours or every 6 years. The airplane’s maintenance logbooks were not recovered, so an exact determination of the time on the propellers was not possible.
The airplane’s fuel system consisted of two separate fuel systems; one in each wing, and each feeding its respective engine via the nacelle (engine feed) tank. Each wing fuel system had a main fuel system composed of multiple interconnected fuel cells that gravity fed the 57-gallon capacity nacelle tank. Each wing had a 79-gallon capacity auxiliary fuel tank located inboard of the engine nacelle, which, if fueled would automatically feed the nacelle tank. Each wing fuel system, including the nacelle tank, had a total fuel capacity of 193 gallons, or a total fuel capacity of 272 gallons per wing when the auxiliary fuel tank was serviced. An engine can be configured to draw fuel from the opposite wing fuel system, if needed, by activating an electric crossfeed valve.
The accident airplane had an empty weight of 8,160 pounds. It had a maximum gross takeoff weight of 12,500 pounds. Two days before the accident, the airplane was fully fueled with the addition of about 380 gallons of jet fuel. At 6.7 pounds per gallon, the fuel weight was 3,645 pounds. The remaining useful load capacity for people and baggage was 695 pounds. There were six adult males on board, and from their California State driver’s licenses, their total weight came to 1,115 pounds. The occupant’s personal baggage was weighed as it was removed from the wreckage and totaled 230 pounds. The airplane was estimated to be approximately 653 pounds overweight at takeoff.
The Beech Super King Air 200 Pilot’s Operating Handbook Limitations section states that the airplane has an Air Minimum Control Speed (Vmc speed) of 86 knots. This is the lowest airspeed at which the airplane is directionally controllable when one engine suddenly becomes inoperative and the other engine is at takeoff power. At airspeeds below Vmc, the rudder is no longer able to overcome the asymmetrical yawing force produced by the remaining operating engine.
This airplane was not equipped with a flight data recorder or cockpit voice recorder. Federal regulations did not require them on this airplane.
At 1040, the reported weather conditions at Long Beach Airport (LGB, elevation 60 feet), were: wind 200 degrees at 3 knots; visibility 10 statute miles; cloud condition, overcast at 800 feet; temperature 61 degrees Fahrenheit; dew point 54 degrees Fahrenheit; altimeter setting 30.13 inches of mercury.
WRECKAGE AND IMPACT INFORMATION
The airplane’s initial point of impact was on an asphalt runway. A ground scar proceeded on a 205-degree magnetic track across flat grass terrain for about 425 feet, where the burned fuselage was found upright on a 300-degree magnetic orientation. The wreckage was located approximately 1,500 feet from the midpoint of its intended departure runway. The debris field leading to the fuselage contained both propeller assemblies, the left engine, and components of both main landing gear. The right wing remained attached to the fuselage and its engine was in place, but remained attached to the airframe only by control cables, electrical wiring, and fuel lines.
The aft portion of the fuselage, from the pressure bulkhead back, and the empennage separated from the main fuselage. It was found lying next to the forward portion of the fuselage and still connected to it by wires and cables. The T-tail stabilizer, with its elevator and trim tab, had separated from the vertical stabilizer and was found approximately 35 feet from the main wreckage. The fuselage exhibited compression buckling, sooting, and thermal discoloration throughout its length. Rescue personnel cut large holes in the fuselage above and aft of the right wing and forward on the left side next to the pilot’s station to facilitate the extrication of the occupants.
Flight control continuity was established from the pilot’s control column and rudder pedals to the ailerons, rudder, and elevator. The flaps were found in the up position and the landing gear in the down position. The power levers, propeller levers, and condition levers on the central pedestal were all found full forward.
The left torque gauge was reading about 700 ft/lbs and the right torque gauge was reading about 1,700 ft/lbs. The maximum rated takeoff torque for the engines was 2,230 ft/lbs. The airframe manufacturer’s representative stated that the torque gauges were powered by alternating current and that their readings should not be considered representative of the torque being developed at impact; the torque gauge system wiring was compromised during the impact sequence.
All of the left wing main fuel tanks, including the left wing nacelle tank, were breached. The left auxiliary fuel tank appeared intact, but did not contain any fuel. With the exception of the inboard center fuel tank, all of the right wing main fuel tanks, including the right wing nacelle tank, were breached. The right auxiliary tank and the right inboard center fuel tank visually appeared intact and contained some liquid, which was consistent with jet fuel. Approximately 30 gallons of fluid were retrieved from these two tanks, and visual inspection of the fluid revealed no evidence of contamination. No airframe anomalies were noted that would have precluded normal flight operations.
On April 19, 2011, a team of investigators from the Transportation Safety Board Canada, Hawker Beechcraft Corporation, and Pratt & Whitney Canada convened to examine the two engines. Over the next 3 days, each engine was photographed, documented, and disassembled. The engine manufacturer’s representative stated that both engines displayed minimal deformation to their external housings, including light compressional and torsional deformation to their exhaust ducts. The left and right engines displayed signatures to their compressor 1st stage, compressor impeller and shroud, compressor turbine vane ring, compressor turbine, 1st stage power turbine vane ring and shroud, 1st stage power turbine, 2nd stage power turbine vane ring and shroud, and 2nd stage power turbine consistent with their making contact with their adjacent components during the impact sequence. These contact signatures were similar throughout both engines. The manufacturer’s representative stated that the similarity
between the contact signatures of the two engines suggests that they were producing symmetrical power at the time of impact, likely in a low to middle power range.
The engines displayed no indications of any pre-impact anomalies or distress that would have precluded normal engine operation prior to impact.
On April 20, 2011, a team of investigators from the FAA, Hawker Beechcraft Corporation, and Hartzell Propeller, Inc., convened to examine the two propeller assemblies. During the examination, each propeller assembly was photographed, documented, and disassembled. The propeller manufacturer’s representative stated that both propellers were severely damaged by impact. The damage to both propellers was remarkably similar, which suggests that they both impacted in a similar manner and were operating at similar power. The blades had multiple bends, twisting, leading edge damage, and the outer 1/3 of one blade was torn off. Tip damage to all blades was relatively mild, which could indicate low power at the time of impact, but could also be attributed to impact at a steep nose down attitude. In general, the blade damage suggested impact with both engines producing power.
There were no pre-impact discrepancies noted that would have precluded normal operation of the propellers.
MEDICAL AND PATHOLOGICAL INFORMATION
The County of Los Angeles, Department of Coroner, performed an autopsy on the pilot on March 17, 2011.
The FAA's Civil Aeromedical Institute (CAMI) in Oklahoma City, Oklahoma, performed toxicology tests on the pilot. According to CAMI's report, the pilot’s blood was tested for carbon monoxide, cyanide, ethanol (volatiles) and drugs with negative results.
TESTS AND RESEARCH
A video study was performed on a recording collected from an airport security camera, located at 33:48:44 north, 118:09:13 west. The wide angle design of the camera’s lens, the storage of frames per second, and the approximate 2,000-foot distance from the camera to the runway resulted in a low quality image of the aircraft. The video was used for estimating the groundspeed of the airplane and its altitude over about 3.5 seconds, from the time about 100 feet above ground level, to the time when the loss of control occurred.
The study results indicate that the accident airplane reached an estimated groundspeed of 130 knots and an altitude slightly greater than 140 feet above the ground. At about 2 seconds into the video, a darker grayish area appears behind the airplane, which could be smoke generated by one of the airplane’s engines. At the same point where the darker grayish area appears, the airplane begins to yaw left, which progressed until the airplane impacted the ground.
The airplane appeared to be flying normally for about 2 seconds of the video. Then it departed to the left of the runway and impacted the ground about 9 seconds later. The darker grayish area appeared and the commencement of the aircraft’s loss of control began approximately above the midpoint of the 10,000-foot-long runway.
Several additional laboratory tests were conducted in support of this investigation. Five fuel samples were obtained from the fuel truck that fueled the airplane. These five 1-gallon samples were sent to Wright-Patterson Air Force Base for testing by the US Air Force’s fuel laboratory. No anomalies with the samples were identified. Additionally, the Honeywell General Aviation Enhanced Ground Proximity Warning System onboard the airplane, the airplane’s warning annunciator panel, and the left and right firewall fuel filter bowl assemblies and their elements were examined. No pertinent information was obtained from these examinations. For further information on these examinations, see the public docket for this investigation.
In mid-February 2012, an FAA inspector from the Long Beach Flight Standards District Office (FSDO) was giving a Part 135 check-ride to a line pilot employed by West Coast Charters, Santa Ana, California. The inspector noticed that, during the pilot’s preflight of a King Air 200 airplane, he did not drain the airplane’s fuel tank sumps. When he questioned the pilot about it, the pilot responded with “we [pilots] don’t do that, the mechanics do that.” The inspector pointed out to the pilot that the Pilot’s Operating Handbook for the airplane requires that the King Air’s 12 fuel tank sumps be drained during preflight before every flight. Follow-up communications between Long Beach FSDO inspectors and the Chief Pilot of West Coast Charters verified that this was standard practice.
The DM for West Coast Maintenance said the King Air’s fuel system has several tanks or cells, which feed the engine’s nacelle inverted “L” shaped (57 gallon) fuel tank. He said maintenance personnel are required to open the nacelle tank every 24 months for inspection and cleaning. When this is done, it is common to find water, debris, and biomicrobial contaminants in the tank. He said the entire engine’s fuel supply must flow to the bottom of this tank. The DM said that regular draining of the King Air’s 12 fuel tank sumps would minimize the water and debris found in the nacelle tank upon inspection.
The DM said that, during the accident airplane’s departure, as the airplane rotated for takeoff, if water was present in the bottom of the nacelle tank, it would shift aft covering the fuel intake port to the engine. This “slug” of water would then flow to the engine’s 14 fuel nozzles, where it could extinguish the engine’s fire; the engine would stop producing power and its propeller would move from coarse to fine pitch.
Subsequently, jet fuel would follow the water, and the engine’s internal heat would likely be sufficient to relight the atomized fuel. The engines were equipped with auto ignition systems, and if they were in the on position, they may also have been triggered to relight the engine. The DM believes that the two pops he heard were attempts by the engine to relight the reintroduced fuel. He said that each pop would have been accompanied by grayish white smoke.
The DM also said that water found in airplane fuel tanks does not necessarily come from contaminated fuel trucks. Airplane refueling trucks have stringent checks and documentation requirements of their filters and are subject to regular tank sump sampling. He believes that the biggest source of introduced water into fuel tanks is daily temperature variations and atmospheric temperature variations. That is, if a fuel tank is not completely full, there is a cavity of air above the fuel, and due to the tank’s venting system, the air in that cavity will move in and out as daily temperature rise and fall, or as the airplane climbs to cruise altitude and descends at its destination.
The United States Air Force has a fuels engineering research laboratory located at Wright-Patterson Air Force Base. One of their Senior Research Engineers stated that “the cavity above fuel in a partially filled fuel tank is vulnerable to aircraft fuel tank breathing through its vent system. This breathing of air, in-and-out, causes water to condense within the fuel tanks.” He said that there are many variables which affect this phenomenon, including: diurnal temperature and pressure variations, flight altitude pressure variations, relative atmospheric humidity, fuel tank size and volume above the fuel, and fuel storage time. The senior engineer further stated that good housekeeping practices of an airplane’s fuel source and regular draining of the fuel tank sumps is the simplest way to reduce the presence of water in aircraft fuel tanks.
The FAA Advisory Circular number 20-43C, titled “Aircraft Fuel Control” states:
“All aviation fuels absorb moisture from the air and contain water in both suspended particle and liquid form. The amount of suspended particles varies with the temperature of the fuel. Whenever the temperature of the fuel is decreased, some of the suspended particles are drawn out of the solution and slowly fall to the bottom of the tank. Whenever the temperature of the fuel increases, water is drawn from the atmosphere to maintain a saturated solution. Changes in fuel temperature, therefore, result in a continuous accumulation of water.”
“The presence of any contamination in fuel systems is dangerous. Laboratory and field tests have demonstrated that when water was introduced into the fuel tank, it immediately settled to the bottom. Fuel tanks are constructed with sumps to trap this water. It is practically impossible to drain all water from the tanks through the fuel lines, so it becomes necessary to regularly drain the fuel sumps in order to remove all water from the system.”
“If left undrained, the water accumulates and will pass through the fuel line to the engine and may cause the engine to stop operating.”
One of the airplane manufacturer’s test pilots stated: “King Air fuel tanks must be drained before every flight, it seems like a little bit of water is always being drained off.”